@Enmy en Efecto Cyberpunk (Paso a paso) 📷 @Enmy with Cyberpunk effect (Step by step)

portada enmy.jpg

Ey chicos, miren a @enmy en neón. Ella vio las entregas anteriores y no pudo aguantar, comentarme en Tik Tok para que le haga uno igual. Puedes comprobarlo aquí

En esta ocasión cambié los colores y nunca pensé que ese verde sería tan luminoso. Creo que lo mejor fue la foto que elegí, aunque pude oscurecer algunas sombras; el brillo que le da es increíble.

La foto original pertenece a una de las sesiones que le realicé.

Hey guys, check out @enmy in neon. She saw the previous installments and couldn't hold out, comment me on Tik Tok so I can make her one just like it. You can check it out here
This time I changed the colors and never thought that green would be so bright. I think the best thing was the photo I chose, although I could darken some shadows; the brightness it gives it is incredible.
The original photo belongs to one of the sessions I did for him.

enmy neon original.jpg

Lo primero que realizaremos será separar a la modelo del fondo. En esta ocasión me demoré un poco por el cabello. Es una parte muy difícil aunque creo que lo hice bien. También vamos a colocar el fondo en negro. Así que en esta parte tendremos 2 capas.

The first thing we will do is to separate the model from the background. This time I took a little bit of time because of the hair. It is a very difficult part but I think I did it well. We are also going to place the background in black. So in this part we will have 2 layers.

enmy neon 1.jpg

Luego escribimos la inicial E, en una fuente gruesa y recta. Para ver la posición con respecto al lienzo y a la modelo, estará de blanco aunque por poco tiempo.

Then we write the initial E, in a thick and straight font. To see the position with respect to the canvas and the model, it will be in white but only for a short time.

enmy neon 2.jpg

Ya en este paso le quitamos el relleno a la letra, dajándolo al 0% en la ventana de capas. Iremos a modo de fusión para colocar el trazo en color blanco, de forma interna y el grosor a nuestro gusto.

In this step we remove the fill from the letter, leaving it at 0% in the layers window. We will go to blend mode to place the stroke in white color, internally and the thickness to our liking.

enmy neon 3.jpg

La capa que contiene la letra la convertimos en objeto inteligente. A este le damos un modo de fusión de "superposición de degradado". Aquí es donde viene el cambio con respecto a los anteriores y fue en el color. Esta vez usé un verde y un magenta tirando a rojo.

We convert the layer containing the letter into a smart object. To this we give a blend mode of "gradient overlay". Here is where the change from the previous ones comes and it was in the color. This time I used a green and a magenta tending to red.

enmy neon 4.jpg

Esta capa la duplicamos con control + J. A eso le aplicamos un desenfoque gausiano. Rasterizamos la capa y la duplicamos dos veces. Después con control + E las vamos a combinar para que sea una sola capa.

We duplicate this layer with control + J. We apply a Gaussian blur to it. Rasterize the layer and duplicate it twice. Then with control + E we are going to combine them to be a single layer.

enmy neon 5.jpg

Activamos la capa de Enmy para verla y procedemos a borrar algunas zonas para que parezca que está dentro de la letra.

We activate the Enmy layer to see it and proceed to erase some areas to make it look like it is inside the letter.

enmy neon 6.jpg

Luego creamos una capa de ajuste de degradado sólido. Usamos los mismos colores de antes, el verde y el magenta. A esta capa le ponemos el modo "color".

Then we create a solid gradient adjustment layer. We use the same colors as before, green and magenta. We set this layer to "color" mode.

enmy neon 7.jpg

Ya @enmy está verde y magenta. Lo que haremos es borrar un poco en la zona de la cara. Para eso usamos el pincel en negro con la máscara de capa activada.

Already @enmy is green and magenta. What we will do is to erase a little in the area of the face. For that we use the brush in black with the layer mask activated.

enmy neon 8.jpg

Ya casi finalizada; vamos a crear un fondo atractivo y que le de al arte dinamismo. Para eso pintaremos en una capa nueva, puntos grandes de los colores usados en el neón. También pintamos algunos puntos blancos más pequeños y en mayor cantidad. Luego le damos a esta capa un desenfoque radial y ese efecto lo repetimos tres veces.

Almost finished; let's create an attractive background that gives the artwork dynamism. For that we will paint on a new layer, large dots of the colors used in the neon. We also paint some smaller and more white dots. Then we give this layer a radial blur and repeat this effect three times.

enmy neon 9.jpg

Este es el resultado final con algunos brillos incluidos.

This is the final result with some glitter included.

enmy neon.jpg

Si te gusta este tipo de efecto te invito a ver los anteriores:

If you like this type of effect I invite you to see the previous ones:

portada trinmar.jpgportada geral.jpg
LinkLink
portada barbara 2.jpgportada nohelia.jpg
LinkLink

Translated with www.DeepL.com/Translator (free version)



0
0
0.000
2 comments
avatar

Great post
if you don't got the 450 HIVE claim it now, i got last night
it's for limited time get it quickly click Here

0
0
0.000